재실 감지 센서 문제 해결

대부분의 경우 점유 감지 센서는 매우 신뢰할 수 있으며, 특히 PIR 점유 동작 감지 센서. 의 경우가 그러합니다. 점유 감지 센서 스위치는 올바르게 설치되고 작동되면 문제없이 완벽하게 작동합니다. 일상적인 사용 중 발생하는 대부분의 문제는 부적절한 설치나 설정으로 인해 발생합니다.

다음은 일반적인 문제점 및 점유 동작 감지 센서 스위치.

목차

• 새로 설치한 점유 감지 센서 스위치로 켜기/끄기가 되지 않음
• 수동 버튼을 눌러도 센서가 반응하지 않음
• 방/공간이 비어 있어도 조명이 계속 켜져 있음
• 새로 설치한 센서 스위치 작동 후 조명이 계속 꺼져 있음
• 사람이 지나갈 때 조명이 켜짐
• 방이 비어 있을 때 조명이 켜짐 
• 방에 사람이 있을 때 조명이 꺼짐
• 조명이 꺼졌다가 즉시 다시 켜짐

새로 설치한 점유 감지 센서 스위치로 켜기/끄기가 되지 않음

추정 원인:

센서 스위치 배선이 잘못되었습니다.

해결 방법: 

점유 감지 센서에 중성선(Neutral wire)이 필요한지 확인하십시오.

• 만약 requires a neutral wire(4 wires), make sure green wire is connected to ground, and white wire connected to neutral.
• 만약 requires only a ground wire(3 wires), make sure green wire is connected to ground.

수동 버튼을 눌러도 센서가 반응하지 않음

추정 원인:

The sensor is under initial power up or power outage, it needs time for initialization.

해결 방법:

Wait 30 seconds for the sensor to be fully functional and press the button again.

방/공간이 비어 있어도 조명이 계속 켜져 있음

추정 원인:

Sensor detecting an external noise source such as an HVAC vent.

솔루션:

• Change sensor sensitivity to low.
• Eliminate or decrease the external noise source.
• Relocate the sensor if possible.

---

추정 원인:

Time out not passed

솔루션:

• Wait for the time dealy to expire.
• Change the time delay to a lower value.

---

추정 원인:

Dual-technology ultrasonic and PIR sensors are placed too close together. 

솔루션:

Relocate the sensors

---

추정 원인:

Sensor is facing rapid temperature change such as a HAVC or coffer maker.

솔루션:

• Change sensor sensitivity to low.
• Replace with a manual override sensor switch
• Replace with a dual technology sensor

---

추정 원인:

Sensor is in manual on/off mode

솔루션:

• Turn off the switch
• Change to occupancy or vacancy mode.

새로 설치한 센서 스위치 작동 후 조명이 계속 꺼져 있음

추정 원인:

Circus breaker switch is in off position

해결 방법:

Turn on the switch

---

추정 원인:

센서 스위치 배선이 잘못되었습니다.

해결 방법: 

점유 감지 센서에 중성선(Neutral wire)이 필요한지 확인하십시오.

• Wire the load wires correctly according to your user manual.
• If it requires a neutral wire(4 wires), make sure green wire is connected to ground, and white wire connected to neutral.
• If it requires only a ground wire(3 wires), make sure green wire is connected to ground.

---

추정 원인:

Sensor connected to an improper voltage

해결 방법:

Check your voltage output to see if it matches the sensor voltage requirement.

---

추정 원인:

Light bulb damaged

해결 방법:

Change your light bulbs.

---

추정 원인:

Sensor in on/off mode, or vacancy mode

해결 방법:

• Change the sensor working mode to occupancy mode
• Manually turn on the switch

---

추정 원인:

Sensor set to ambient light sensing mode when ambient light is too bright

해결 방법:

• Change the ambient light level to none.
• Change the ambient light level to a proper value.

---

추정 원인:

Sensor not detecting motion

해결 방법:

• Relocate the sensor switch to proper position
• Change sensor sensitivity to high.

---

추정 원인:

Sensor not have full-view of the room/space

해결 방법:

• Relocate the sensor to proper position.
• Move the object which blocks the sensor’s detection range.

사람이 지나갈 때 조명이 켜짐

추정 원인:

Sensor coverage extends beyond room perimeter

해결 방법:

Change sensor sensitivity to low.

---

추정 원인:

Sensor detects motion from mirror or shiny objects reflections outside the room.

해결 방법:

• Change sensor sensitivity to low.
• Switch to manual on/off mode
• Cover and block some part of the sensor to reduce its sensitivity.

---

추정 원인:

Turns on in vacancy mode

해결 방법:

•  Lights can turn back on within 30 seconds following the time delay timeout. Meaning users should wait for another 30 seconds when the time delay expires, then the light is completely switched off and can be only turned on by manual action.
• Sensor Mode may be set to occupancy mode other than vacancy mode.

방이 비어 있을 때 조명이 켜짐

추정 원인:

Sensor triggered by activity outside the coverage area.

해결 방법:

• Change sensor sensitivity to low.
• Switch to manual on/off mode
• Cover and block some part of the sensor to reduce its sensitivity.

---

추정 원인:

Ultrasonic sensor detecting airflow from an HVAC duct.

해결 방법:

• Change sensor sensitivity to low.
• Eliminate or decrease the external noise source.
• Relocate the sensor if possible.

---

추정 원인:

Sensor is facing rapid temperature change such as a HAVC or coffer maker.

해결 방법:

• Change sensor sensitivity to low.
• Replace with a manual override sensor switch
• Replace with a dual technology sensor

방에 사람이 있을 때 조명이 꺼짐

추정 원인:

Sensor’s timeout is too short for this application

해결 방법:

Change time delay to a proper value.

---

추정 원인:

Room is too large for sensor’s coverage.

해결 방법:

Install additional sensor switches

---

추정 원인:

Improperly located to not have full view of room

해결 방법:

• Relocate the sensor switch
• Move blocking objects avay from the sensor dection coverage.

---

추정 원인:

Sensitivity adjusted to low

해결 방법:

Change sensor sensitivity to high

---

추정 원인:

Pir damaged

해결 방법:

Replace with a new sensor.

---

추정 원인:

Improper height

해결 방법:

Relocate the sensor switch to a proper height according to your user manuall guide.

조명이 꺼졌다가 즉시 다시 켜짐

추정 원인:

There is a heat source that changes its temperature rapidly

해결 방법:

• Block and cover part of the sensor to decrease its sensitivity.
• Switch to manual mode.