What is Phase-Controlled Dimming
Phase-controlled dimming is a method used to regulate the brightness of a lamp or lighting system by adjusting the conduction time of electricity within an AC power wave cycle. This technique is commonly employed in residential settings due to its cost-effectiveness and ease of installation. By reducing or increasing the power entering the lamp, phase-controlled dimming allows for lower or higher brightness levels, respectively.
人感センサーを活用した省エネソリューションをお探しですか？
PIR人感センサー、人感センサー搭載省エネ製品、人感センサースイッチ、商業施設向けOccupancy/Vacancy（在室/不在）ソリューションについては、お気軽にお問い合わせください。
This dimming method falls under the category of primary side regulation (PSR), where brightness control is achieved from the primary side of the circuit. It typically utilizes phase-cutting dimmers, which control the conduction time of electricity within the AC power wave cycle to modulate the lamp’s brightness. There are two types of phase-cut dimming modes: leading edge (forward phase) mode and trailing edge (reverse phase) mode. Leading edge mode initiates the input power from a non-zero point within the wave cycle, while trailing edge mode starts from the zero point.
To ensure optimal dimming performance, it is crucial to use a phase-cutting controller in conjunction with a compatible phase-cutting driver. This compatibility ensures smooth and reliable dimming without issues such as light flashing or poor performance. Phase-controlled dimming offers a cost-effective and convenient solution for adjusting the brightness of lamps and lighting systems in residential applications.
こちらの商品もおすすめです
- 無電圧接点リレー出力付き天井取り付け型PIR人感センサー
- 12/24VDCまたは12/24VAC低電圧電源
- EMS、HVAC、および建物制御入力用COM、NO、NC絶縁リレー接点
- 低電圧DC天井埋め込み型マイクロ波人感センサースイッチ
- 10～30 VDC範囲の12 VDC / 24 VDC入力
- 調整可能なタイムラグ、照度（Lux）閾値、感度を備えた最大動作電流10A仕様
- 高負荷対応型 埋込型天井取付けマイクロ波人感センサースイッチ
- 100-265 VAC 商用電源入力、10Aモデル
- 調整可能なタイムラグ、照度（Lux）閾値、感度を備えた5.8 GHzマイクロ波検知
- 埋込型天井取付けマイクロ波人感センサースイッチ
- 100-265 VAC商用電圧入力、5Aモデル
- 調整可能なタイムラグ、照度（Lux）閾値、感度を備えた5.8 GHzマイクロ波検知
- 220V電源対応 天井取付けRZ037 PIR（赤外線）人感センサー調光器
- 定格負荷660W、最大動作電流3A
- LUXボタンによる照度センサーのON/OFFおよびユーザー設定の調光明るさ制御
- 110V電源対応 天井取付けRZ037 PIR（赤外線）人感センサー調光器
- 定格負荷330W、最大動作電流3A
- LUXボタンによる照度センサーのON/OFFおよびユーザー設定の調光明るさ制御
- 低電圧DC対応 天井取付けマイクロ波人感センサースイッチ
- 10～30 VDC範囲の12 VDC / 24 VDC入力
- 調整可能なタイムラグ、照度（Lux）閾値、感度を備えた最大動作電流10A仕様
- 高負荷対応 天井取付型マイクロ波人感センサースイッチ
- 100-265 VAC 商用電源入力、10Aモデル
- 調整可能なタイムラグ、照度（Lux）閾値、感度を備えた5.8 GHzマイクロ波検知
- 天井取り付け型マイクロ波人感センサースイッチ
- 100-265 VAC商用電圧入力、5Aモデル
- 調整可能なタイムラグ、照度（Lux）閾値、感度を備えた5.8 GHzマイクロ波検知
- 低電圧DC埋込型天井PIR人感センサースイッチ
- 10～30 VDC範囲の12 VDC / 24 VDC入力
- 最大動作電流10A（調整可能なタイムラグ、照度閾値、感度設定付き）
- 高負荷対応 埋込型天井PIR人感センサースイッチ
- 100-265 VAC 商用電源入力、10Aモデル
- 360度検知（調整可能なタイムラグ、照度閾値、感度設定付き）
- 埋込型天井PIR人感センサースイッチ
- 100-265 VAC商用電圧入力、5Aモデル
- 360度検知（調整可能なタイムラグ、照度閾値、感度設定付き）
- 屋内用照明ON/OFF制御ワイヤレススイッチ＆受信機キット
- 100-230VAC、50/60Hz、定格電流5A受信機
- 2.4GHz通信対応 CR2032電池駆動ワイヤレススイッチ
- Occupancy（自動点灯/自動消灯）
- 12–24V DC (10–30VDC)、最大10A
- 360°検知エリア、直径8–12m
- タイムラグ 15秒–30分
- 照度センサー オフ/15/25/35 Lux
- 高/低感度
- 自動点灯/自動消灯人感モード
- 100–265V AC, 10A（中性線必須）
- 360°検知範囲、検知直径8–12 m
- タイムデレイ15秒–30分、Lux OFF/15/25/35、感度 高/低
- 自動点灯/自動消灯人感モード
- 100–265V AC, 5A（中性線必須）
- 360°検知範囲、検知直径8–12 m
- タイムデレイ15秒–30分、Lux OFF/15/25/35、感度 高/低
- 100V-230VAC
- 伝送距離：最大20m
- ワイヤレス人感センサー
- 有線制御
よくある質問
Is ELV and 0-10v Dimming the Same
The DIM0-10VELV is a module designed to convert a 0-10V dimming signal to an ELV reverse phase dimming signal, which is compatible with ELV dimmable lighting products. This module enables the use of standard 0-10V dimming control dimmers with ELV dimmable lighting products, and it can smoothly dim down to 1%. Therefore, ELV and 0-10V dimming are not the same, but the DIM0-10VELV module can bridge the gap between them.
What Type of Dimming Is Best for LED
The most suitable dimming option for LED light bulbs is trailing edge dimmers, while leading-edge dimmers are more compatible with conventional incandescent and halogen light bulbs.
What Happens if You Use the Wrong Dimmer With LED Lights
Existing dimmer switches typically have a minimum power requirement of 50W. However, when using LED lights with a dimmer switch that has a higher minimum power requirement, the lights may not reach the minimum power threshold. As a result, the dimmer switch may become confused, causing the lights to flicker and emit a buzzing noise.
Why Do My Lights Keep Dimming and Getting Brighter
When your lights become brighter, it indicates that they are receiving an excessive amount of voltage. Conversely, when they dim, it suggests that they are receiving insufficient voltage. If this issue persists, it could potentially lead to your electrical devices being exposed to either excessive or inadequate power, resulting in potential damage.
What Is the Difference Between a Dimmer and a ELV Dimmer
An ELV dimmer is specifically designed to dim the electronic power supply of a low voltage halogen light. Unlike a regular dimmer, an ELV dimmer cuts the trailing edge of the power wave in order to reduce hum. Therefore, ELV, Trailing Edge, and Reverse Phase all refer to the same functionality.
Can I Use a Regular Dimmer on 0-10v
A regular dimmer should not be used on a LED light fixture that has a 0-10v or 1-10v dimming driver, as it can damage the driver. It is important to note that a LED fixture that supports line voltage dimming cannot be wired to a 0-10v or 1-10v dimmer.
