What is Single Pole Light Switch
A single pole light switch is a common type of switch which controls the operation of a light fixture or electrical outlet from a single location. It is a straightforward and widely used switch option. Unlike double-pole switches, which are more commonly found in industrial settings, single pole switches are typically found in residential and small-scale commercial applications.
A single pole light switch consists of two brass terminal screws and a toggle labeled with ON and OFF positions. These switches also typically include a grounding screw that connects to the circuit’s ground wire. The purpose of the switch is to control the flow of electricity to the connected light fixture or outlet. By flipping the toggle, the circuit can be either completed or broken, allowing for the control of the electrical current.
您可能也會感興趣
- 吸頂式 PIR 人體感應器，配備乾觸點繼電器輸出
- 12/24VDC 或 12/24VAC 低電壓供電
- 用於 EMS、HVAC 和建築控制輸入的 COM、NO 和 NC 隔離繼電器觸點
- 低壓直流嵌入式天花安裝微波人體感應開關
- 12 VDC / 24 VDC 輸入，支援 10-30 VDC 範圍
- 最大工作電流 10A，配備可調節延時、光感閾值及靈敏度
- 高負載嵌入式天花安裝微波人體感應開關
- 100-265 VAC 市電輸入，10A 型號
- 5.8 GHz 微波感應，配備可調節延時、光感閾值及靈敏度
- 嵌入式天花安裝微波人體感應開關
- 100-265 VAC 市電輸入，5A 型號
- 5.8 GHz 微波感應，配備可調節延時、光感閾值及靈敏度
- 適用於 220V 電源的天花安裝 RZ037 PIR 被動式紅外線佔空感應調光開關
- 最大工作電流 3A，額定負載 660W
- LUX 按鈕控制光線感應器開關及用戶設定之調光亮度
- 適用於 110V 電源的天花安裝 RZ037 PIR 被動式紅外線佔空感應調光開關
- 最大工作電流 3A，額定負載 330W
- LUX 按鈕控制光線感應器開關及用戶設定之調光亮度
- 低壓直流天花安裝微波人體感應開關
- 12 VDC / 24 VDC 輸入，支援 10-30 VDC 範圍
- 最大工作電流 10A，配備可調節延時、光感閾值及靈敏度
- 高負載吸頂式微波動態感應器開關
- 100-265 VAC 市電輸入，10A 型號
- 5.8 GHz 微波感應，配備可調節延時、光感閾值及靈敏度
- 吸頂式微波動態感應器開關
- 100-265 VAC 市電輸入，5A 型號
- 5.8 GHz 微波感應，配備可調節延時、光感閾值及靈敏度
- 低壓直流嵌頂式 PIR 動態感應器開關
- 12 VDC / 24 VDC 輸入，支援 10-30 VDC 範圍
- 最大工作電流 10A，具備可調式時間延遲、光照度閾值及靈敏度
- 高負載嵌頂式 PIR 動態感應器開關
- 100-265 VAC 市電輸入，10A 型號
- 360度偵測，具備可調式時間延遲、光照度閾值及靈敏度
- 嵌頂式 PIR 動態感應器開關
- 100-265 VAC 市電輸入，5A 型號
- 360度偵測，具備可調式時間延遲、光照度閾值及靈敏度
- 用於室內開關照明控制的無線開關及接收器套裝
- 100-230VAC，50/60Hz 接收器，額定電流 5A
- CR2032 電池供電無線開關，採用 2.4GHz 通訊
- 佔用感應（自動開啟/自動關閉）
- 12–24V DC (10–30VDC)，最高 10A
- 360° 覆蓋，直徑 8–12 米
- 延遲時間 15 秒至 30 分鐘
- 光感應器 關閉/15/25/35 Lux
- 高/低靈敏度
- 自動開啟/自動關閉佔用模式
- 100–265V AC，10A（需接零線）
- 360° 全方位覆蓋；8–12 米偵測直徑
- 延遲時間 15 秒至 30 分鐘；Lux 關閉/15/25/35；靈敏度 高/低
- 自動開啟/自動關閉佔用模式
- 100–265V AC，5A（需接零線）
- 360° 全方位覆蓋；8–12 米偵測直徑
- 延遲時間 15 秒至 30 分鐘；Lux 關閉/15/25/35；靈敏度 高/低
- 100V-230VAC
- 傳輸距離：最遠 20 米
- 無線動態感應器
- 有線控制
During installation, connect two hot wires to the single pole light switch. One terminal of the switch is used to connect to the incoming power-source wire, while the other terminal is used for the outgoing hot wire to the fixture or outlet. This configuration enables the switch to effectively control the flow of electricity.
正在尋找動態感應節能解決方案？
歡迎聯絡我們以獲取完整的 PIR 動態感應器、動態感應節能產品、動態感應器開關以及人體感應／無人感應商業解決方案。
常見問題
Does It Matter Which Wire Goes Where on a Light Switch
It is not important which wire goes where on a light switch because the switch terminals can be interchanged.
Can I Replace a Double Pole Switch With a Single Pole Switch
Yes, it is possible to replace a double pole switch with a single pole switch. The process involves using only one side of the double pole switch instead of both. Essentially, a double pole switch is essentially two single switches combined, allowing for control in two different locations.
Which Type of Switch Is Commonly Used in Residential Houses
The most frequently used switch in residential houses is the single-pole switch. It is equipped with two terminals and is responsible for turning the power on or off. On the other hand, a three-way switch consists of three terminals, while a four-way switch has four terminals.
