RZ040 無線開關及接收器套裝

RZ040

RZ040 無線開關與接收器套件無需鋪設新開關電線,即可為室內照明新增開關控制。100-230VAC 接收器連接至燈具,而由 CR2032 電池供電的無線開關則可從固定於牆面或手持的位置發送 2.4GHz 控制訊號。

此套件出廠時已完成配對,支援 20 米室內通訊,每個控制器最多可配對 5 個開關,並具備多套件頻道選擇功能。適用於不便新增有線開關位置的照明改裝工程。
閱讀更多

產品亮點

  • 照明改裝控制: 無需鋪設新開關電線至該位置,即可新增額外的控制點。
  • 100-230VAC 接收器: 直接接線至燈具,切換所連接燈具的開啟或關閉狀態。
  • 無線發射器: 由 CR2032 電池供電的開關可以使用隨附的貼紙固定於牆上,或作為手持遙控器使用。
  • 20 米室內通訊: 2.4GHz 接收器/發射器通訊,支援 20 米室內距離。
  • 多開關配對: 每個控制器最多可配對 5 個無線開關,以實現多個控制點。

快速出貨:99% 現貨供應

完整動態感應產品系列

立即查詢 適用於大宗 ODM/OEM 訂單

RZ040 無線開關及接收器套件

無需新增開關電線,即可新增無線照明控制

當不便鋪設新開關電線時,RZ040 無線開關與接收器套件可為室內照明新增開關控制。接收器接線至照明電路,而由電池供電的無線開關則可安裝於使用者需要控制的位置。

適用於照明改裝、房間佈局變更,以及傳統牆面底盒位置不理想時新增控制點。無線開關可放置於牆面、傢俬或玻璃上,亦可作為手持遙控器使用。

Indoor room with ceiling light for RZ040 wireless lighting control context

接收器與發射器作為預先配對的照明套件運作

接收器由 100-230VAC 供電並連接至燈具。按下無線開關會向接收器發送 2.4GHz 訊號,從而切換所連接燈具的開啟或關閉狀態。

接收器與發射器在出廠時已預先配對,可即時使用。僅在重設、變更頻道或向同一控制器新增額外無線開關時,才需要重新配對。

功能、優勢、規格

RZ040 無線開關套件結合了 100-230VAC 接收器、CR2032 供電發射器及 2.4GHz 控制,方便安裝人員在訂購前核實傳輸範圍、配對、負載及安裝細節。

RZ040 receiver and emitter wireless switch application diagram

功能與優勢

  • 無線開關擺放位置: Mount the emitter on a wall, furniture, or glass, or use it as a handheld remote when a fixed switch box is not available.
  • Line-Voltage Receiver: The receiver is powered by 100-230VAC, 50/60Hz and wires directly to the lighting fixture for ON/OFF control.
  • 2.4GHz Communication: The emitter sends a 2.4GHz signal to the receiver when pressed, giving the kit wireless control between the two components.
  • Factory Pre-Paired Kit: The receiver and emitter are pre-paired for immediate use, so standard setup does not require a pairing step.
  • 多開關配對: One controller can pair with up to 5 wireless switches, giving installers multiple control points for the same light.
  • Channel Selection: When multiple kits are used within 120 meters, receivers can be assigned channels 1-7 to avoid cross-control.
  • Indicator Feedback: The emitter flashes red after a press, while the receiver uses green and red indicator states for power, ready, and activation feedback.
  • Low Battery Warning: The emitter warning pattern indicates when the CR2032 battery should be replaced.
Controller (Receiver)

電源

100-230VAC, 50/60Hz

Rated current

5A

Wireless frequency

2.4GHz

Communication range

20 meters indoor

工作溫度

-20~+50°C

工作濕度

<93%RH

Terminal labels

N1, N, L, L1

Supported load categories

LED bulb, incandescent/halogen, fluorescent/ballast, LED ceiling lamp, LED tube

Wireless Switch (Emitter)

電源

1 x CR2032 battery

Wireless frequency

2.4GHz

Communication range

20 meters indoor

工作溫度

-10~40°C

工作濕度

<93%RH

Mounting/use

Wall fixed with double-sided sticker or portable handheld use

Pairing capacity

Up to 5 switches per controller

Low battery warning

Below 2.2V, the switch stops working and the LED warning flashes

常見問題

Can the RZ040 add a light switch without new switch wiring?

Yes. The receiver is wired to the lighting fixture, while the wireless switch sends a 2.4GHz signal from the selected control location. This avoids running a new switch cable to that location.

What power does the receiver need?

The controller receiver is powered by 100-230VAC, 50/60Hz and is rated at 5A. It should be installed by disconnecting power first and wiring the terminal block correctly.

What battery does the wireless switch use?

The wireless switch emitter uses 1 CR2032 battery. The RZ040W switch ships with the battery pre-installed; remove the insulation pull tab before first use.

How far can the wireless switch communicate indoors?

The manual lists a 20 meter indoor communication range between the emitter and receiver. Avoid installing the receiver inside a metal enclosure because metal can reduce or block wireless transmission.

Can one receiver work with more than one wireless switch?

Yes. One controller can pair with up to 5 wireless switches. If more switches are paired, the oldest switch pairing is removed automatically.

When should channel selection be used?

Channel selection is only required when multiple kits are used within 120 meters. Assign a different channel number from 1-7 to each receiver to avoid cross-control.

What loads can the RZ040 control?

The manual lists LED bulbs, incandescent/halogen loads, fluorescent/ballast loads, LED ceiling lamps, and LED tubes as supported load categories. Do not overload the receiver.

Where can the wireless switch be mounted?

The emitter can be wall-fixed with the provided double-sided sticker, placed where control is convenient, or used as a portable handheld remote within the indoor transmission range.

EU rz022 佔用感應器 c2a

擴展您的動態感應器產品線

檢視我們所有的動態感應器節能產品

商品評價

目前沒有評價。

搶先評價 “RZ040 Wireless Switch and Receiver Kit”

Chinese