What is Preheat
Preheat, in the context of the lighting industry, refers to the practice of applying a minimal amount of electricity to the filament or fixture of a lamp before fully powering it on. This technique is employed to enhance the lifespan of filament lamps and prevent thermal shock to the filaments. By preheating the lamp, it begins to emit a low-level glow, allowing it to reach the desired brightness more quickly when additional current is applied. As a result, the process of turning on the lights becomes smoother, avoiding the sudden “shock” of activating them from a cold state.
正在尋找動態感應節能解決方案？
歡迎聯絡我們以獲取完整的 PIR 動態感應器、動態感應節能產品、動態感應器開關以及人體感應／無人感應商業解決方案。
Preheating is particularly beneficial for incandescent lamps, especially in colder environments during winter months. By preheating the lamps to a low percentage of power, typically around 3%, before focusing starts, it helps to prevent lamps from blowing due to the cold temperature. This precautionary measure is also applicable to dimmable LEDs, as the internal components of these fixtures require a small amount of current to “wake up” before they can gradually fade up. Preheating with a low-level current aids in achieving a more gradual and seamless transition in the dimming curve of LEDs, preventing them from abruptly turning on.
Moreover, preheating can contribute to the longevity of traditional gels used in lights. By preheating the lights, it helps to extend the lifespan of these gels. Overall, preheating is a technique employed in the lighting industry to increase the lifespan of lamps, prevent thermal shock, and achieve smoother dimming curves. It involves applying a minimal amount of electricity to the filament or fixture before fully powering it on, ensuring a more efficient and reliable lighting experience.
您可能也會感興趣
- 吸頂式 PIR 人體感應器，配備乾觸點繼電器輸出
- 12/24VDC 或 12/24VAC 低電壓供電
- 用於 EMS、HVAC 和建築控制輸入的 COM、NO 和 NC 隔離繼電器觸點
- 低壓直流嵌入式天花安裝微波人體感應開關
- 12 VDC / 24 VDC 輸入，支援 10-30 VDC 範圍
- 最大工作電流 10A，配備可調節延時、光感閾值及靈敏度
- 高負載嵌入式天花安裝微波人體感應開關
- 100-265 VAC 市電輸入，10A 型號
- 5.8 GHz 微波感應，配備可調節延時、光感閾值及靈敏度
- 嵌入式天花安裝微波人體感應開關
- 100-265 VAC 市電輸入，5A 型號
- 5.8 GHz 微波感應，配備可調節延時、光感閾值及靈敏度
- 適用於 220V 電源的天花安裝 RZ037 PIR 被動式紅外線佔空感應調光開關
- 最大工作電流 3A，額定負載 660W
- LUX 按鈕控制光線感應器開關及用戶設定之調光亮度
- 適用於 110V 電源的天花安裝 RZ037 PIR 被動式紅外線佔空感應調光開關
- 最大工作電流 3A，額定負載 330W
- LUX 按鈕控制光線感應器開關及用戶設定之調光亮度
- 低壓直流天花安裝微波人體感應開關
- 12 VDC / 24 VDC 輸入，支援 10-30 VDC 範圍
- 最大工作電流 10A，配備可調節延時、光感閾值及靈敏度
- 高負載吸頂式微波動態感應器開關
- 100-265 VAC 市電輸入，10A 型號
- 5.8 GHz 微波感應，配備可調節延時、光感閾值及靈敏度
- 吸頂式微波動態感應器開關
- 100-265 VAC 市電輸入，5A 型號
- 5.8 GHz 微波感應，配備可調節延時、光感閾值及靈敏度
- 低壓直流嵌頂式 PIR 動態感應器開關
- 12 VDC / 24 VDC 輸入，支援 10-30 VDC 範圍
- 最大工作電流 10A，具備可調式時間延遲、光照度閾值及靈敏度
- 高負載嵌頂式 PIR 動態感應器開關
- 100-265 VAC 市電輸入，10A 型號
- 360度偵測，具備可調式時間延遲、光照度閾值及靈敏度
- 嵌頂式 PIR 動態感應器開關
- 100-265 VAC 市電輸入，5A 型號
- 360度偵測，具備可調式時間延遲、光照度閾值及靈敏度
- 用於室內開關照明控制的無線開關及接收器套裝
- 100-230VAC，50/60Hz 接收器，額定電流 5A
- CR2032 電池供電無線開關，採用 2.4GHz 通訊
- 佔用感應（自動開啟/自動關閉）
- 12–24V DC (10–30VDC)，最高 10A
- 360° 覆蓋，直徑 8–12 米
- 延遲時間 15 秒至 30 分鐘
- 光感應器 關閉/15/25/35 Lux
- 高/低靈敏度
- 自動開啟/自動關閉佔用模式
- 100–265V AC，10A（需接零線）
- 360° 全方位覆蓋；8–12 米偵測直徑
- 延遲時間 15 秒至 30 分鐘；Lux 關閉/15/25/35；靈敏度 高/低
- 自動開啟/自動關閉佔用模式
- 100–265V AC，5A（需接零線）
- 360° 全方位覆蓋；8–12 米偵測直徑
- 延遲時間 15 秒至 30 分鐘；Lux 關閉/15/25/35；靈敏度 高/低
- 100V-230VAC
- 傳輸距離：最遠 20 米
- 無線動態感應器
- 有線控制
