RZ037-DRY Ceiling Mount PIR Occupancy Sensor with Dry Contact Relay
RZ037-DRY 是一款天花板安裝式 PIR 佔用感應器，配備隔離乾接點繼電器輸出，適用於 EMS、HVAC 及樓宇控制輸入。
它支援 12/24VDC 或 12/24VAC 供電，並提供 COM、NO 及 NC 繼電器接點，讓控制系統可接收佔用狀態，而無需由感應器直接切換線電壓負載。
- 隔離乾接點繼電器輸出，配備 COM、NO 及 NC 接點
- 繼電器接點額定值最高為 30VDC 及 1A
- 從天花板位置進行 360 度 PIR 佔用偵測
- 可調校時間延遲、Lux 水平及高／低靈敏度
- 專為低電壓控制系統佈線而設，並非用於高電壓負載切換
产品亮点
- 乾接點輸出： 隔離式 COM、NO 及 NC 繼電器接點讓控制系統可接收佔用狀態，而無需切換線電壓照明。
- 低電壓電源： 支援 12/24VDC 或 12/24VAC 輸入，適用於控制面板及低電壓系統安裝。
- 天花 PIR 覆蓋範圍： 從天花板安裝位置提供 360 度被動紅外線佔用感測。
- 現場設定： 內置按鈕可調校時間延遲、Lux 閾值及高／低靈敏度。
不是您要找的？ 查看我们的产品组合：
咨询专家
Dry-Contact Occupancy Sensing For Control Systems
The RZ037-DRY adapts the RZ037 ceiling PIR sensor format for low-voltage control systems that need an occupancy signal instead of a directly switched lighting load.
Its isolated relay provides Common, Normally Open, and Normally Closed contacts, making it suitable for EMS, HVAC, and building control inputs where the controller decides what action follows occupancy detection.
Connect Occupancy Sensing To Building Controls
Use the dry-contact output when a control panel, HVAC controller, or energy management input needs to know whether a space is occupied without placing the sensor in the main load circuit.
Installers can choose the NO or NC contact logic according to the receiving system, then tune the time delay, Lux level, and PIR sensitivity from the sensor body after wiring.
Features, Benefits, Specs
RZ037-DRY combines ceiling PIR occupancy detection, 12/24V AC/DC power, and isolated COM/NO/NC contacts so installers can verify coverage, relay logic, and setup values before ordering.
Features & Benefits
- Isolated dry-contact relay: COM, NO, and NC outputs support control-system inputs instead of direct line-voltage load switching.
- 12/24V AC/DC supply: The sensor can be powered from 12/24VDC or 12/24VAC low-voltage control power.
- 360-degree PIR detection: Ceiling-mounted passive infrared sensing covers occupancy around the sensor position.
- Adjustable time delay: Select 15 seconds through 30 minutes to match testing, passageway, restroom, or work-area behavior.
- Selectable Lux control: Off, 15 Lux, 25 Lux, and 35 Lux settings let installers decide when ambient light should hold the relay off.
- High/low sensitivity: The sensor can be tuned for the expected movement pattern and room conditions.
- Clear wire identification: Red and black provide input power, while green, orange, and yellow provide NC, COM, and NO relay wiring.
- Features
-
Product type
Ceiling-mounted PIR occupancy sensor with dry-contact relay output
Input voltage
12/24VDC or 12/24VAC
Relay contacts
Normally Closed (NC), Common (COM), Normally Open (NO)
Relay rating
COM input 30VDC max; NC/NO output 1A max
Cable wires
Red IN+, Green NC, Orange COM, Yellow NO, Black IN-
Sensor type
Passive infrared (PIR)
Detection range
360 degrees
Detection diameter
8-12m when ambient temperature is below 27C
Motion detection speed
0.6-1.5m/s
Installation height
2.5-3.5m
Time delay
15s, 30s, 1min default, 3min, 5min, 10min, 30min
Light sensor level
Off, 15Lux, 25Lux default, 35Lux
Sensitivity
High or Low
Working temperature
-10 to +40C
Working humidity
<93% RH
FAQ
What makes RZ037-DRY different from the line-voltage RZ037 models?
RZ037-DRY provides an isolated dry-contact relay output for a control system input. It is not specified as a direct line-voltage lighting load switch like the high-voltage RZ037 variants.
What power supply does RZ037-DRY need?
The manual specifies 12/24VDC or 12/24VAC input power. Red is IN+ and black is IN- in the supplied wiring diagram.
Which dry-contact wires are available?
The relay output provides green for Normally Closed, orange for Common, and yellow for Normally Open. Choose NO or NC logic according to the receiving EMS, HVAC, or building control input.
Can this sensor be used with EMS or HVAC systems?
Yes. The product description in the manual identifies EMS and HVAC systems as target integrations, with occupancy communicated through the internal isolated relay dry contact.
What coverage should installers expect?
The manual specifies 360-degree detection with an 8-12m detection diameter when ambient temperature is below 27C, and a recommended installation height of 2.5-3.5m.
Which setup values can be adjusted?
Installers can adjust time delay, light sensor level, and sensitivity. Time delay options range from 15 seconds to 30 minutes, Lux options include Off, 15Lux, 25Lux, and 35Lux, and sensitivity can be set to High or Low.
Why might the sensor not trigger immediately after power is restored?
The manual notes that when power is first turned on or restored, the sensor will not automatically control the load for the first one minute.
商品評價
目前沒有評價。