{"id":19733,"date":"2025-12-12T08:56:13","date_gmt":"2025-12-12T08:56:13","guid":{"rendered":"https:\/\/staging.rayzeek.com\/uncategorized\/rayzeek-sensor-audit"},"modified":"2025-12-12T09:00:09","modified_gmt":"2025-12-12T09:00:09","slug":"rayzeek-sensor-audit","status":"publish","type":"post","link":"https:\/\/staging.rayzeek.com\/sv\/blogg\/rayzeek-sensor-audit","title":{"rendered":"The “Tape-Over” Audit: Commissioning Rayzeek Sensors to Survive Reality"},"content":{"rendered":"

There is a specific, sinking feeling that comes with a phone call at 7:00 AM from a facility manager. The panic isn’t usually about the main switchgear or the panel schedules; it\u2019s about a single office where the lights won\u2019t stay on, or a hallway where they won\u2019t turn off. These are the nuisance calls that destroy margins. A sensor that saves 15% theoretical energy but turns off on a CEO during a Zoom call is a sensor that gets taped over. Once a layer of black electrical tape goes over the lens, that sensor saves exactly 0% energy.<\/p>

\"A
When sensors annoy users, the ‘tape-over’ solution destroys any potential energy savings.<\/figcaption><\/figure><\/div>

Hardware isn’t usually the problem. The Rayzeek RZ-series units are robust workhorses, but they ship with a fatal flaw: “Factory Defaults.” These settings are designed for a showroom or a test lab, not for a drafty masonry building in Detroit or a glass-walled conference room in Chicago. If you install them straight out of the box, relying on the “Plug and Play” promise, you are essentially scheduling your own return trip.<\/p>

Reliability has to take priority over efficiency during commissioning. That doesn’t mean you ignore energy codes. It means acknowledging that a lighting control system only works if the tenants tolerate it. If they hate it, they will bypass it. To prevent the callback, you have to commission for human behavior, not just for watts.<\/p>

Deconstructing the Dual-Tech Trap<\/h2>

Most modern specs call for Dual-Technology sensors\u2014combining Passive Infrared (PIR) and Ultrasonic detection. On paper, this looks like the perfect marriage. In the field, it often causes the “ghost switching” that convinces tenants their building is haunted.<\/p>

H\u00e4mta inspiration fr\u00e5n Rayzeeks r\u00f6relsesensorportf\u00f6ljer.<\/h3>

Hittar du inte det du vill? Oroa dig inte. Det finns alltid alternativa s\u00e4tt att l\u00f6sa dina problem. Kanske kan en av v\u00e5ra portf\u00f6ljer hj\u00e4lpa.<\/p>

PIR-r\u00f6relsesensorer<\/p><\/a><\/div><\/div>

R\u00f6relsesensoromkopplare<\/p><\/a><\/div><\/div>

N\u00e4rvarosensorer<\/p><\/a><\/div><\/div>

R\u00f6relsesensor f\u00f6r luftkonditionering<\/p><\/a><\/div><\/div>

R\u00f6relsesensorljusremsor<\/p><\/a><\/div><\/div>

L\u00e5gsp\u00e4nnings DC-r\u00f6relsesensorer\/dimmers<\/p><\/a><\/div><\/div>

Tr\u00e5dl\u00f6sa r\u00f6relsesensorset<\/p><\/a><\/div><\/div><\/div><\/div>

PIR relies strictly on line-of-sight to detect heat in motion. It catches a person walking into a room perfectly, but it has a major blind spot: it cannot see through partitions, high-back chairs, or restroom stalls. If you rely on PIR alone in a complex space, you get the “waving arms” phenomenon, where office workers have to perform calisthenics every 20 minutes just to keep the lights on.<\/p>

Ultrasonic fills that gap. It floods the room with high-frequency sound waves and listens for the Doppler shift caused by movement. It sees around corners and over stall doors. Unfortunately, it also “sees” things that aren’t people. Ultrasonic sensors are notorious for detecting the vibration of a VAV box ramping up, the rattle of a loose diffuser, or even the airflow from a forced-air heater vent.<\/p>

This is where the default settings betray you. Most units ship with both PIR and Ultrasonic sensitivities set to “High” or “Auto.” In a quiet hallway at 3 AM, when the heat kicks on, a high-sensitivity Ultrasonic sensor interprets that air movement as occupancy. The lights trigger. The facility manager sees the bill. You get the blame.<\/p>

The Sensitivity Dial Protocols<\/h2>

Fixing this requires getting physical with the sensor. Pop the faceplate off. Underneath, usually hidden behind a secondary plastic guard, you will find the trimpots\u2014those tiny dials that require a 1\/8th inch “tweaker” screwdriver to adjust.<\/p>

The Ultrasonic Rule of 70%<\/strong>\nIf the sensor sits anywhere near an HVAC supply vent, never leave the Ultrasonic dial at the 12 o’clock (50%) or 5 o’clock (100%) position. Dial it back. A safe starting point for hallways and open offices is roughly 70% sensitivity. You want it sensitive enough to catch a walking person, but deaf to the vibration of the drop ceiling. If you are in a room with heavy airflow, dial it down to 50% or even lower. You are trading a bit of range for the guarantee that the lights won’t ghost-switch all night.<\/p>

The Restroom Exception<\/strong>\nRestrooms require the opposite approach. This is the one place where you max out the Ultrasonic sensitivity. The partitions in a multi-stall restroom effectively blind the PIR lens. If a user sits in a stall for five minutes, PIR will assume the room is empty. You need the Ultrasonic waves to bounce off the tile and over the stall doors to detect minor motion. If you leave a restroom sensor on factory default (often a balanced mix), you risk plunging someone into darkness at a very vulnerable moment. That is a callback you do not want to take personally.<\/p>

The Timeout Battle: 15 vs 30 Minutes<\/h2>

The dip switches next to the trimpots control the timeout\u2014the delay before lights extinguish after motion stops. Factory defaults usually sit at an aggressive 15 minutes\u2014sometimes even 10. This looks great on an energy model, but it is terrible for an accountant working on an Excel spreadsheet.<\/p>

People in deep concentration sit incredibly still. We don’t move enough to trigger standard PIR thresholds, and if the Ultrasonic is dialed back to avoid HVAC interference, the sensor might not catch typing fingers. The result is the “Reading in the Dark” problem. The lights go out. The user waves their arms. They get annoyed. After the third time, they call maintenance.<\/p>

Unless you are strictly bound by a local code that explicitly forbids it (like certain aggressive interpretations of Title 24), set the timeout to 30 minutes. Yes, you might burn 15 minutes of extra electricity when someone leaves for lunch. But compare that cost to the $350 ticket for a truck roll to come back and flip a dip switch. Or compare it to the cost of the user disabling the sensor entirely. A 30-minute timeout is the “peace of mind” setting. It covers the gaps in human movement and ensures the system feels invisible, rather than intrusive.<\/p>

Kanske \u00e4r du intresserad av<\/h3>
\"\"<\/div><\/a><\/div>

RZ037-DRY Takmonterad PIR-upptagningssensor med torrkontaktrel\u00e4<\/a><\/h4><\/div>